Short version: Trane and American Standard Heating & Air Conditioning are two brand names stamped on the same equipment coming off the same La Crosse, Wisconsin factory floor. American Standard Companies acquired The Trane Company in 1984 and ran both brands on shared production lines. Ingersoll-Rand took over the HVAC side in 2008; the parent renamed itself Trane Technologies in 2020. That is why a Trane XV80 and an American Standard Freedom 80 furnace share the same CNT3776 ignition module, SEN0297 flame sensor, SFCAP45D5440R dual-run capacitor, VAL9031 gas valve, and Climatuff scroll compressor from the Trane OEM catalog.
This guide maps the legacy unit lines across both brands and pairs each failure mode with the shared Trane OEM parts stocked at HVACMORE — with real 2026 prices and SKUs. For related brand-focused coverage, see the Goodman, Janitrol, and GMC Legacy Parts Guide, the Furnace Buying Guide 2026, the Furnace Diagnosis Chat-Style guide, and the Control Board Visual Diagnosis guide.
Who are Trane and American Standard?
The Trane Company was founded in 1913 in La Crosse, Wisconsin by Reuben Trane and his father James, originally as a plumbing shop that moved into steam heating and then into commercial and residential HVAC. By the 1950s Trane was one of the largest HVAC companies in North America, known for commercial chillers and residential furnaces. The La Crosse plant still produces Trane and American Standard commercial and residential equipment today.
American Standard Companies was founded in 1875 (as the Standard Sanitary Manufacturing Company) and became a global plumbing fixtures and HVAC conglomerate across the 20th century. The HVAC side of American Standard entered residential heating and cooling by acquiring Mueller Climatrol in 1949. In 1984 American Standard Companies acquired The Trane Company, consolidating the plumbing-HVAC parent with the La Crosse HVAC pure-play. From 1984 onward Trane and American Standard were run as sister brands on the same production lines.
2007 to today. In 2007 American Standard Companies split itself into three independent public companies: American Standard Brands (plumbing fixtures, later acquired by LIXIL), WABCO Holdings (commercial vehicle controls, later acquired by ZF Friedrichshafen), and Trane Inc. (the HVAC business, carrying both the Trane and American Standard HVAC brands). In 2008 Ingersoll-Rand acquired Trane Inc. for $10.1 billion. In 2020 Ingersoll-Rand spun off its industrial segment and the remaining HVAC parent renamed itself Trane Technologies. Both Trane and American Standard continue as co-branded HVAC lines under Trane Technologies today.
The practical consequence: an American Standard Platinum 80 furnace built in 2008 and a Trane XV80 built the same year are the same cabinet with a different sticker on the door. The parts under the hood are catalogued under Trane OEM numbers.
Which legacy units did Trane and American Standard build?
Four product families run across both brand stamps.
Gas furnaces. On the Trane side, the model prefixes are XV, XC, XB, XR, S-series (S8X1, S9V, S9V2), and TUH / TUE / TDC in the older product-code system. On the American Standard side, the matching families are Platinum (variable-speed, 2-stage or modulating), Gold (fixed-speed 2-stage), Silver (single-stage), and Freedom series, with product codes ADD, AUD, AVD, AYD, AUH. A Trane XR80 single-stage 80% is mechanically the same unit as an American Standard Freedom 80.
Residential split condensers. Trane model prefixes: 4TTR (R-410A single-stage), 4TTB (budget single-stage), 4TTX (2-stage), 4TTV (variable-capacity), XB13, XR14, XR15, XR16, XR17, XV17/XV18, XL15i/XL20i. American Standard equivalents: 4A6H series (Platinum variable), 4A7A series (Gold 2-stage), 4AC series (Silver single-stage), AccuComfort variable models.
Residential heat pumps. Trane: 4TWR, 4TWX, XV18/XV19, XR15, XL15i/XL20i heat pumps. American Standard: 4A6H heat pumps, Platinum/Gold/Silver heat pump lines.
Air handlers. Trane: TAM4, TAM7, TAM8, TAM9, TEM3, TEM6, TEM8. American Standard: matching AM4, AM7, AM8, AEM3, AEM6, AEM8. These share evaporator coils, blower motors, inducer motors, control boards, and refrigerant metering devices across the two brands.
Every one of these cabinets came off the same assembly line. The brand on the door is cosmetic; the OEM part numbers in the Trane catalog are what fit for repair.
Why the parts cross both brands
Three structural reasons the parts are interchangeable.
Same factory, same assembly line. Trane and American Standard residential equipment is built in La Crosse, Wisconsin and Tyler, Texas on the same tooling. The components installed on the cabinet — ignition modules, flame sensors, ignitors, inducer blowers, blower motors, capacitors, contactors, gas valves, pressure switches, transformers, and compressors — come from the same supplier catalog with the same OEM Trane part numbers.
Climatuff compressors are Trane-made. The scroll compressors in both Trane and American Standard residential condensers and heat pumps are Trane Technologies’ own Climatuff brand, manufactured in Tyler, Texas. The exact same Climatuff scroll unit at the same tonnage and refrigerant combination installs in a Trane XR14 and an American Standard Silver 14 — same mounting, same suction/discharge orientation, same electrical spec. The COM-prefix Trane part numbers are the cross-reference.
Backward-compatible supersessions. When Trane updates a part (for example, replacing an older CNT ignition module with a newer CNT revision or a KIT package), the superseding part is engineered to drop into both Trane and American Standard cabinets of the previous generation without rewiring. That is how a 2003 American Standard Freedom 80 can take a 2026 Trane CNT3776 24V 3TFI ignition module without a wiring harness change.
Shared control boards and ignition modules
The ignition control board (and on sealed-combustion models, the ignition module) is the brain of a residential Trane or American Standard furnace. The CNT prefix is the Trane OEM control-board line and crosses both brands.
The CNT3776 24V 3TFI ignition module is the single most-ordered legacy Trane / American Standard furnace board. It covers the mid-1990s through mid-2000s XR80 / Freedom 80 / Platinum 80 cabinets. On a no-ignition call where the inducer runs but no ignitor glow and no gas valve click, the module is usually the suspect after confirming 24V transformer output.
Shared ignitors and flame sensors
Hot surface ignitors fail on a predictable 4-to-8-year schedule on Trane and American Standard furnaces from thermal cycling. Flame sensors oxidize over time and lose their microamp signal — often the cheapest fix on a legacy unit.
The IGN0023USA Norton 271N and IGN0145 silicon-nitride ignitors cross both Trane and American Standard gas furnace lineups from the mid-1990s onward. For diagnosis of a no-ignition call, see the Furnace Diagnosis Chat-Style guide.
Shared capacitors, contactors, and transformers
The capacitors, contactors, and transformers in Trane and American Standard condensers and air handlers are the same industry-standard parts carried under the Trane SFCAP, SFCTR, and TRR OEM prefixes. These cross both brands and in most cases also cross to universal replacements where cost matters more than OEM paperwork.
Match the stamped MFD rating on the old capacitor and the amperage rating on the old contactor before ordering. The SFCAP45D5440R 45/5 MFD dual-run is the most-ordered single part across all of HVACMORE’s Trane/American Standard capacitor sales.
Shared gas valves and pressure switches
The gas valve opens on a 24V signal from the ignition module and sends gas to the burners. The pressure switch confirms the inducer blower is actually pulling draft before the module allows the valve to open. Both parts use the Trane VAL and SWT OEM prefixes, which cross both brands.
Shared blower motors and inducer blower assemblies
Blower motors move conditioned air through the ductwork; inducer blower assemblies pull combustion products out through the flue. Both are catalogued under Trane MOT and BLW OEM numbers that cross American Standard cabinets of the same era.
Climatuff scroll compressors are available at HVACMORE under Trane COM-prefix part numbers across the full tonnage and refrigerant range (2 to 15 ton, R-22 / R-410A / R-454B). Due to current product-photography availability, compressors are not shown in a slider here — call HVACMORE at 855-575-4822 with the condenser model, serial, and refrigerant for a compressor cross-reference. For the full compressor replacement decision tree (bare swap vs full condenser), see the York Compressor Replacement Guide 2026.
Worked example: American Standard Freedom 80 that won’t ignite
A homeowner calls about a 2003 American Standard Freedom 80 upflow gas furnace, model AUD080R9V3. The symptom: thermostat calls for heat, inducer blower starts and runs, ignitor glows briefly then goes dark, gas valve never clicks, and the furnace locks out on the third try. The ignition module LED flashes a steady 2-flash code.
Diagnosis. The 24V transformer measures 25.7 VAC across its secondary — good. The pressure switch closes on inducer start — good. The ignitor measures 61 ohms cold — within spec. The flame sensor is clean and reads 3.1 microamps in bench test. But the gas valve never receives its 24V signal. Suspect: ignition module output stage has failed.
Part. Open the ignition module cover, read the stamp: CNT3776 24V 3TFI. The AUD080R9V3 uses the same Trane CNT3776 ignition module as the matching Trane XR80 of the same vintage — same wiring harness, same mounting, same fault code chart. Order a Trane CNT3776 at $416.99 at HVACMORE, swap it in, cycle power. Thermostat calls, inducer starts, pressure switch closes, ignitor glows, gas valve clicks, flames come up, flame sensor confirms, blower engages at the end of the fan-on delay.
Why this works. The American Standard Freedom 80 and the Trane XR80 are the same cabinet with different stickers on the door, built in La Crosse, Wisconsin on the same production line in 2003. The Trane CNT3776 OEM module is factory-authorized for both.
For the step-by-step diagnosis walkthrough on no-ignition calls (24V output testing, pressure switch bench test, ignitor resistance check, flame microamp measurement), see the Furnace Diagnosis Chat-Style guide and the Control Board Visual Diagnosis guide.
When the OEM part number on the data plate is discontinued
Legacy Trane and American Standard OEM parts have official Trane supersessions. A supersession is a new current Trane part number that replaces the obsolete one — electrically equivalent, physically compatible, and factory-authorized for the original cabinet. HVACMORE’s parts team maintains an internal cross-reference of these supersessions.
To get the right supersession:
1. Cabinet model and serial number. Both are on the data plate.
2. The old OEM number. Stamped on the part itself. CNT for control boards and modules, SFCAP for capacitors, SFCTR for contactors, TRR for transformers, SWT for pressure switches, VAL for gas valves, SEN for flame sensors, IGN for ignitors, MOT for motors, BLW for inducer blowers, COM for compressors, WHL / FAN for blower wheels, BAY for accessories.
3. Call HVACMORE at 855-575-4822. For an out-of-warranty condenser where the OEM cost does not pencil out, universal cross-references are available: ICM Controls control boards, Supco universal hot surface ignitors, Mars 2 and ICM dual-run capacitors, Packard contactors, Supco SPP6E universal hard start kits (see the compressor guide for the full universal hard start lineup). For in-warranty systems or any Trane / American Standard furnace control board, OEM supersession is strongly preferred to preserve warranty coverage and keep the LED fault code chart valid.
[Sourcing CTA image goes here — 28-sourcing-cta.svg. Delete this line after uploading.]
Browsing the full Trane OEM catalog
Everything in the sliders above and more is in the Trane vendor section of HVACMORE at hvacmore.com/search?q=trane. The lineup covers both Trane- and American Standard-stamped legacy equipment under Trane OEM part numbers, organized by product type: control boards, ignition modules, pilots & ignitors, flame sensors, pressure switches, gas valves, capacitors, contactors, transformers, blower motors, inducer blower assemblies, blower wheels, and compressors. If the OEM number stamped on the old part matches a current Trane SKU, it ships from the HVACMORE warehouse.
For related brand-focused coverage on legacy equipment, see the Goodman, Janitrol, and GMC Legacy Parts Guide, the Furnace Buying Guide 2026, the HVAC Repair vs Replace 2026 guide, and the HVAC Lifespan 2026 guide. For diagnosis across any brand, see the Furnace Diagnosis Chat-Style guide, the AC Diagnosis Chat-Style guide, and the Control Board Visual Diagnosis guide.
Frequently asked questions
Are Trane and American Standard the same company? Yes, under the same corporate roof since 1984. American Standard Companies acquired Trane in 1984; Ingersoll-Rand bought the HVAC side in 2008; the parent is now Trane Technologies (renamed 2020). American Standard Heating & Air Conditioning is the sister brand to Trane.
Can I use a Trane control board on an American Standard furnace? Yes, if the Trane CNT part number matches the stamp on the old board. Common cross-fits: CNT3776 ignition module, CNT7941 control board, CNT1537 ICM fan control, CNT09418 2-stage control board.
What is a Climatuff compressor? Trane Technologies’ own scroll compressor brand, built in Tyler, Texas. The same Climatuff unit installs in both Trane and American Standard residential condensers at matching tonnage and refrigerant.
What is the most common failed part on a Trane or American Standard furnace? Flame sensor (SEN0297 at $45.99 or SEN2662 at $33.99), then hot surface ignitor (IGN0023USA Norton 271N at $56.54 or IGN0145 silicon-nitride at $92.99), then ignition module (CNT3776 at $416.99).
Where is the data plate on a Trane or American Standard unit? Furnace: behind the blower door on the inside wall of the burner compartment. Condenser / heat pump: outside of the compressor service panel. Air handler: inside the service access door.
Can I replace an American Standard gas valve with a Trane gas valve? Yes, if the VAL stamped number matches. Common cross-fits: VAL9028, VAL9029, VAL9030, VAL9031, VAL7731.
What capacitor fits an American Standard Silver 14 condenser? Match the stamped MFD. Trane SFCAP45D5440R 45/5 MFD ($32.99) is the most common cross for mid-tonnage units.
What inducer blower fits a Trane XV80 or American Standard Freedom 80? Trane BLW1137 ($447.99), BLW1139 ($723.99), BLW1321 ($467.99), BLW1322 ($399.99), or BLW0361 ($590.17) depending on cabinet size and stage count.
Do Trane and American Standard condensers share hard start kits? Yes. The BAYKSKT263 ($227.99) and BAYKSKT260 ($143.93) fit both brands. Universal ICM and Supco hard starts work electrically on older out-of-warranty units.
What should I do if the OEM part number is faded or discontinued? Call HVACMORE at 855-575-4822 with the cabinet model, serial, and whatever remains of the stamped part number. The parts team maintains the Trane supersession cross-reference internally.
Need help identifying a legacy Trane or American Standard part?
If the OEM number on the old part is faded, missing, or does not cross directly to a current Trane SKU, call HVACMORE at 855-575-4822. Have the cabinet model number, serial number, and a photo of the old part ready. The parts team maintains an internal cross-reference of legacy Trane and American Standard supersessions and can confirm the correct current OEM in a single call.
For orders by SKU directly, start the search at hvacmore.com/search?q=trane. For broader diagnosis before swapping parts, see the Furnace Diagnosis Chat-Style guide and the Control Board Visual Diagnosis guide.
Sources
- Trane Technologies plc — tranetechnologies.com (corporate parent, 2020 rename)
- The Trane Company — trane.com (current residential OEM parts catalog)
- American Standard Heating & Air Conditioning — americanstandardair.com (sister brand catalog, same equipment)
- Ingersoll-Rand 2008 acquisition announcement — SEC filings (public merger documentation)
- U.S. Environmental Protection Agency — Section 608 refrigerant handling
- U.S. Department of Energy — Furnaces and Boilers
- HVACMORE Trane parts search — hvacmore.com/search?q=trane
Prices and part availability pulled from hvacmore.com on 2026-10-23. Pricing and stock subject to change — verify at the linked product page before ordering, or call HVACMORE at 855-575-4822.
Ready to upgrade your system?
Free ZIP-based pricing on top-rated HVAC systems
Get instant local pricing and expert help choosing the right AC, furnace, or heat pump for your home.
Shop HVAC Systems
